Install the app
How to install the app on iOS

Follow along with the video below to see how to install our site as a web app on your home screen.

Note: This feature may not be available in some browsers.


Brewing Test phenylpropinate.

flyingfox

Iron Killer
Jacked Immortal
Mutated
EG Cash
4,245
Looking for some advice on this, I may get some test phenylpropinate and would like to brew it at 150 or 200 mgs per ml. Could I use the standard 2/20 BA/BB? I am also considering using MCT oil in this or perhaps a blend as I hear MCT flows nicely due to its low viscosity. Adding a small percentage of EO is also on the table....thoughts?
 
Test pp will have PIP like a mofo at 150-200. Any lab that has PIPless test pp 150-200...well its not 150-200. You can get away with 125/ml with minimal pip. So, yes if you wanna dose that high phenyl prop ester your gonna need EO..I would do it all in EO or 50/50. TBH, I dose my 100mg Test PP at 110mg per ml and its the smoothest shit since creamy peanut butter! I use 2/20 in safflower or GSO. Now...if you do go 150...put your solvents in first...gently heat them up....then add in all of powder...use glass stir rod and stir trying to dissolve all particles....now...gently reheat the solution for afew minutes.....and then restir and you will see all the particles completely dissolve...ahhhh....now add in maybe 50 percent of your oil carrier...reheat mix.....then add in the other half...reheat and mix again...there you go..perfectly blended and dissolved .....now filter through .22u and ba bam...beautiful light golden oil.....enjoy. I advise dosing at 110mg...its my fav ester for test and is super smooth when brewed "the long way" like I mentioned above...use solvents first....after all particles are fully dissolved add in oil...you could add in all oil at once tbh....but I like slow cooking my ribs if you catch my drift!


also don't heat to high...remember we are just mixing, we don't need to induce a chemical reaction (which in this case would be destroying some hormone) just enough to get it to properly dissolve...if you see small black particle in middle bottom of beaker/flask...burnt hormone
 
Thanks for the advice JD! I will have to do a test batch and see how bad the PIP is at 150, if its bad I could always blend it with something. BTW I love your "slow brew" process, thanks for sharing! I will let you know how it turns out

Also what is is a good temp for dissolving the hormone?
 
yes, there is...I will have to look around in my notes and books and shit...but...tbh....I heat up water to just before boiling...set it on cool surface...and wait a few minutes then put my solvents or hormone or whatever in there...not too hot....remember just enough to dissolve, nothing more nothing less....I never get it too hot....now when working with primo and you have to get a little technical...but when that water is pretty hot to touch....your good. set it off for a couple and set that beaker in!....never too hot, just dissolve!
 
JDB3 took the words right out of my mouth!
Fox I would be needing one trial vial when you get done to verify your quality! Lol
 
smoove said:
JDB3 took the words right out of my mouth!
Fox I would be needing one trial vial when you get done to verify your quality! Lol

You got it brother! Waiting on the Raws.
 
Thanks for the slow brew process JD. I have some test-pp waiting to be drewed along with a few other compounds. Just waiting for my laboratory to come available.....lol
 

Create an account or login to comment

You must be a member in order to leave a comment

Create account

Create an account on our community. It's easy!

Log in

Already have an account? Log in here.

Similar threads

Latest threads

Back
Top